A tri-function booster/buffer pedal that gives you tons of headroom
The ultra quiet Boost 'n' Buff v.2 Guitar Effects Pedal, from MI Effects, offers up to a 35dB boost
and has a Class A, (single transistor) design. In the lower gain range, the Boost 'n' Buff stompbox is a flat booster (<15db).
In the upper range, it's a treble booster (>15db). In bypass mode, it's an ultra high input impedance buffer (5Meg!). The
Boost 'n' Buff guitar pedal is simple to operate with Volume and Gain Controls and a Heavy Duty 3PDT On/Off footswitch. Operates
off 18V (2 x 9V batteries) internal power or an external power supply (sold separately).
Bypass Mode/Buffer: In bypass mode, the MI Audio Boost 'n' Buff acts as an ultra high input impedance/low
noise buffer. The input impedance is approximately 5 Meg. With such a high input impedance, your guitar pickups don't need
to deliver a lot of current in order to reproduce their full natural bandwidth. You can drive cable lengths as long as you
like without sacrificing tone, and due to the ultra low noise design, you can use the Boost 'n' Buff out the front of dirt
pedals or high gain amps without worrying about introducing any significant noise.
By adding the Boost 'n' Buff in
your signal chain, especially near the front of your effects, you'll notice that in bypass mode your guitar signal will have
a bit more sparkle and top end detail. It's not that there are any special EQing 'tricks', but rather that the Boost 'n' Buff
is faithfully reproducing all of the frequencies that are coming out of your guitar. Your tone will feel a bit more powerful,
with more punch and almost as if there's more dynamic range and 'sustain' (although these are not the right words to describe
it). You've got to try it out to feel what I'm talking about.
Flat Booster: In the first half of the
volume sweep, the frequency response of the Boost 'n' Buff is flat. This provides you with about 15db of flat boost before
the frequency response of the pedal starts to become more treble booster-like. This is perfect for solo volume boosts. The
one thing to note is that if you're going to use digital effects in your signal path, I'd suggest putting the Boost 'n' Buff
after the digital effects to avoid overloading the A/D converters.
Using the Boost 'n' Buff in the FX loop of an amp
to act as a secondary volume control. Since it has ample headroom, line level signals are not a problem. So even if your FX
loop is line level, you can still get quite a bit of boost using the Boost 'n' Buff. This way, your FX loops can also double
as a solo volume booster as well as a standard FX loop. By putting the Boost 'n' Buff in the FX loop, you can use it to boost
the volume of an overdrive channel. If you're using the overdrive channel of your amp, then putting any booster between the
guitar and amp will just increase the amount of distortion as opposed to increasing volume. By putting it AFTER the preamp
(in the FX loop), you can achieve volume boosting without affecting preamp tone.
Treble Booster: Once
past the halfway point, the mid and high frequencies start to climb faster than the low frequencies. At maximum gain, not
only do you have an amazing amount of boost (approximately 35db), but the frequency response is perfectly tailored to driving
a valve amp. It's literally like hot-rodding your amp with an extra tube stage. Also, with the 18V headroom, your sound will
be 'cleaner' going into the amp, so that there's less colouring from the transistor.
The new Boost 'n' Buff pedal now
features an output volume control. This can be used in a few different ways. Firstly, you can now turn down the volume, and
use the built in gain of the Boost 'n' Buff to get mild dirt sounds. Secondly, you can now use the pedal in the treble booster
range at any volume. Finally, by mixing the relative levels of volume and gain, you can now coax a wider range of timbres
from the pedal.
MI Audio Boost 'n' Buff v.2 Guitar Effects Pedal Features:
- Huge 35db Boost range.
- Ultra quiet, Class A (single transistor) design.
- Tri-function booster/buffer
- In bypass mode, it's an ultra high input impedance buffer (5Meg!)
- In the lower gain range, it's a flat booster (<15db)
- In the upper range, it's a treble booster (>15db)
- Huge headroom, with 18V (2*9V battery) internal power.
- Volume and Gain Controls
- Heavy Duty 3PDT footswitch for true bypass and no signal loss
- Professionally powder-coated and silk-screened
- Heavy duty mechanical footswitch.
- External DC Jack for power connection, up to 25V DC.
- Version 2 of the new Boost 'n' Buff now features new graphics and an output volume control.
- Compact enclosure measures 4.3" x 2.2"
Give your rig the boost it needs! Order today.